1.1Embossed pillars in a film
A patterned die presses a square array of 8 µm diameter pillars on a 20 µm pitch into a heated fluoropolymer sheet. Water rests on the low surface energy pillar tops and bridges the air gaps between them.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A patterned die presses a square array of 8 µm diameter pillars on a 20 µm pitch into a heated fluoropolymer sheet. Water rests on the low surface energy pillar tops and bridges the air gaps between them.
A porous alumina nanoparticle layer is deposited on a substrate and heat-treated to form necks between particles. Stearic acid adsorbs to exposed alumina through its carboxyl groups, leaving hydrocarbon tails facing outward. The treated rough surface retains air beneath resting water droplets.
Silica particles with a mean diameter of 120 nm receive a polydimethylsiloxane coating with a mean thickness of 3 nm. The coated particles dry into a porous layer whose polymer-covered asperities support water above air-filled interstices.
A fluorinated acrylic copolymer is deposited from solution onto silica nanoparticles. During drying, the coated particles form a rough porous layer, and the fluorinated side chains lower the surface energy at the water interface.
A rotating low-pressure drum tumbles dry silica nanoparticles while a vaporized fluorinated acrylate monomer and activated initiator form a polymer film on exposed particle surfaces. The powder is pressed onto a tacky tie layer, which anchors the particles while leaving their upper surfaces exposed.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A film of polydimethylsiloxane-coated silica nanoparticles covers the downward-facing lip of an outdoor grain transfer chute. A spray pass deposits the solvent dispersion onto the cleaned lip, and solvent evaporation leaves a continuous agglomerated film. The rough, low-energy surface reduces the area of contact with rain droplets, which roll off the lip under gravity.
Polyisobutylene replaces polydimethylsiloxane as the shell material on alkyl-treated silica nanoparticles. A mixing vessel combines the particles with polyisobutylene dissolved in toluene, and the resulting dispersion is sprayed onto a cleaned metal panel. As the solvent evaporates, the polymer deposits on the particle surfaces and binds neighboring particles at their contacts. The particle clusters supply surface roughness, and the hydrocarbon shells present a low-energy surface to water.
The coating uses silica particles with an average diameter of 600 to 800 nm and an average polydimethylsiloxane shell thickness of 25 to 35 nm. The ratio of average particle diameter to average shell thickness spans approximately 17:1 to 32:1 across these settings. A spray gun deposits the dispersion in two passes with a 60-second flash interval between passes. The deposited particles form a continuous agglomerated layer and retain surface relief on the scale of the particle diameter.
A ventilated rainscreen assembly carries metal panels whose exterior faces bear a continuous film of polydimethylsiloxane-coated nanoparticles. The film is sprayed and dried before the panels are fastened to vertical rails with a drainage cavity behind them. The coated faces shed droplets toward the lower edges, and water that enters the panel joints drains through the cavity.
A batch controller meters a nanoparticle dispersion and a polydimethylsiloxane solution into a stirred vessel using mass flow sensors. The controller calculates the polymer dose from the measured solids feed, the lot-specific particle surface area, and a retained-polymer fraction established from calibration batches. After mixing, an automated spray head deposits the dispersion onto a test coupon and dries the film. A camera measures the angle of a dispensed water droplet and flags batches that miss the acceptance setpoint.
A robot sprays a dispersion of polydimethylsiloxane-coated nanoparticles onto a fixture-mounted metal panel. After a flash interval, a camera under fixed oblique illumination measures image texture and maps low-coverage regions using calibration coupons with known coating mass per area. The controller schedules a localized spray pass over those regions while tapering the deposited dose at the edges. Final drying consolidates the overlapping deposits into a continuous agglomerated film.
A spray nozzle deposits a dispersion of polydimethylsiloxane-coated silica nanoparticles onto aluminum in overlapping passes. As the carrier evaporates, the particles collect into connected clusters and the polymer at particle contacts cures.
Hydroxylated alumina nanoparticles are contacted with silanol-terminated polydimethylsiloxane and then dried. Surface hydroxyl groups react with terminal silanols during heating, anchoring the polymer coating to the alumina cores.
Silica nanoparticles with a mean core diameter of 80 nm receive polymer shells with a mean radial thickness of 8 nm. Transmission electron microscopy with shell contrast resolves the core and shell boundaries for both measurements.
Silica nanoparticles are dispersed in heptane and mixed under shear with vinyl-terminated polydimethylsiloxane and a silicone crosslinker. The mixture is applied to a substrate, and heating removes the heptane and cures the polymer on the particles.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The aforementioned dispersion liquid after the reaction was cooled down to a room temperature, and then a 10-fold molar quantity of ethanol serving as a poor solvent relative to the InP/ZnS core/shell semiconductor nanoparticles was added to the dispersion liquid. Thus, an InP/ZnS agglomerates were obtained.B · US 2013/0153837 A1 · ¶ 79
Each polymer-encapsulated particle has a diameter that is less than 1 micron, and includes a solid particle core, and a polymer coating established directly on the solid particle core.A · US 2011/0079756 A1 · abstract
An empty cell means only that no passage was reproduced there.
The production of such particles often involves multiple steps.A · US 2011/0079756 A1 · ¶ 2
This advantageously eliminates the need to perform a post-polymerization step to remove water in exchange for the non-aqueous medium.A · US 2011/0079756 A1 · ¶ 7
When it comes to use these semiconductor nanoparticles as a fluorescence diagnostic agent, luminance per particle thereof is still far insufficient.B · US 2013/0153837 A1 · ¶ 3
Therefore, as a method of improving luminance, a method is considered in which core/shell semiconductor nanoparticles are aggregated to improve luminance per particle.B · US 2013/0153837 A1 · ¶ 5
patent.fyi, US 2026/0357074 A1, claim 1, first published 2026-11-20T10:10:52-05:00, https://patent.fyi/US20260357074/, SHA-256 16cd622f5adcc609ab17efab26f813b416dba8b8aa35ae59cd04cfd3264132de