1.1Dry nitrogen pretreatment bake
A purged furnace heats the coated strip to 350 °C under flowing nitrogen. Heat removes water and consolidates the phosphate film, while the low oxygen content limits oxidation at openings in the forsterite layer.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A purged furnace heats the coated strip to 350 °C under flowing nitrogen. Heat removes water and consolidates the phosphate film, while the low oxygen content limits oxidation at openings in the forsterite layer.
A temperature-controlled cooling section brings the pretreated strip to 150 °C, and an electrostatic applicator deposits a ground phosphate-silicate glass frit. A subsequent bake at 800 °C fuses the frit into an insulating film.
A roll coater applies an aqueous aluminum phosphate and colloidal silica dispersion to the pretreatment layer. A staged oven first removes free water, then holds the strip at 350 °C to dehydrate the phosphate binder and consolidate the silica-filled film.
A roll coater applies the silica sol to the forsterite, where the liquid wets the surface and enters its pores. Baking at 400 °C removes water and bonds the silica particles into a thin layer that anchors the insulating topcoat.
The alcohol ethoxylate lowers the surface tension of the phosphate and colloidal silica dispersion so that the wet film spreads across the pretreatment during roll coating. The organic wetting agent decomposes during baking, while the phosphate and silica form the insulating film.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
Place X-ray fluorescence gauges upstream of pretreatment application, after the pretreatment bake and cooling section, and after the final bake and cooling section. Match measurements to strip position with a line encoder, and use calibration curves from weighed coupons to convert the baseline-corrected phosphorus signals to dry coating mass for each formulation. Subtract the pretreatment contribution from the final signal when estimating topcoat mass. Use the travel time from each coater to its downstream gauge to schedule feedback adjustments to the corresponding metering roll speed.
Install a scanning infrared pyrometer between the forced-gas cooling section and the insulating topcoat applicator. Calibrate its emissivity setting against contact measurements on coupons carrying the baked pretreatment, and use the highest measured temperature across the strip as the controller input. Modulate cooling blower speed to hold a 90 °C target and reduce strip speed if the blower reaches its upper limit. Lift the applicator rolls when a strip segment above 100 °C reaches the coating station, using the line encoder to track the segment.
The bath contains 80 parts by mass of micronized alumina per 100 parts by mass of aluminum phosphate solids. Agitation keeps the alumina suspended during roll coating, and baking at 750 °C consolidates the phosphate binder around the electrically insulating particles.
A reverse roll coater meters the pretreatment liquid onto the forsterite-coated strip. A continuous furnace heats the strip to 350 °C under nitrogen containing 0.5 vol % hydrogen.
Deionized water and aluminum dihydrogen phosphate form the pretreatment bath, with no chromium compound added. Elemental analysis of the bath checks that total chromium stays below 0.10 parts by mass per 100 parts by mass of phosphate solids.
A chromium(III) nitrate solution supplies 0.25 parts by mass of elemental chromium per 100 parts by mass of phosphate solids. The batch calculation uses the measured chromium concentration of the stock solution to set the addition.
The roll coaters target dry coating masses of 1.0 g/m² for the pretreatment and 3.5 g/m² for the insulating layer on each side. Single-side witness coupons track the mass added by each layer after baking and verify a combined coating mass of 4.5 g/m².
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The coating may be cured under appropriate conditions, for example by baking at from about 275° F. to about 375° F. for between about 15 and about 60 minutes, before applying an additional coating layer over the electrodeposited coating layer.A · US 2010/0163418 A1 · ¶ 46
A gas turbine engine article includes a substrate and a bond coating that covers at least a portion of the substrate with a step formed in at least one of the substrate and the bond coating. A thermally insulating topcoat is disposed on the bond coating.B · US 2016/0040548 A1 · abstract
Metal automotive vehicle bodies (the “body-in-white”) and parts, for instance, are given a many-step treatment of cleaning in one or more cleaning baths or spray tanks, application of an aqueous phosphate coating material as a metal pretreatment step in a phosphating bath, then various rinses and additional finishing treatments, such as described in Claffey, U.S.A · US 2010/0163418 A1 · ¶ 3
An empty cell means only that no passage was reproduced there.
We disclose a composition and process for electrodepositing an electrocoat coating on a metal substrate, which may be an unphosphated metal substrate (that is, a metal substrate that has not undergone a phosphate pretreatment) in which the electrocoat coating provides excellent corrosion protection.A · US 2010/0163418 A1 · ¶ 6
Elimination of the steps and equipment for the phosphating pretreatment process permits a major cost savings in construction of a new paint shop, as well as a simplification and cost savings in operating paint shops now in automotive manufacturing plants.A · US 2010/0163418 A1 · ¶ 6
Therefore, there is a need to increase the longevity of protective coatings in gas turbine engines.B · US 2016/0040548 A1 · ¶ 5
In one exemplary embodiment, a gas turbine engine article includes a substrate and a bond coating that covers at least a portion of the substrate with a step formed in at least one of the substrate and the bond coating.B · US 2016/0040548 A1 · ¶ 6
patent.fyi, US 2026/0357078 A1, claim 1, first published 2026-11-20T10:10:52-05:00, https://patent.fyi/US20260357078/, SHA-256 2ebc7199be3fda91ff257898f85f9f3fe2efaefb7dc6b6ddc1ddcf4303a0743b