1.1Silver nanoparticle ink
A water and glycol carrier suspends the silver nanoparticles for aerosol deposition. After deposition, heating removes the carrier and sinters adjacent nanoparticles into a conductive trace.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A water and glycol carrier suspends the silver nanoparticles for aerosol deposition. After deposition, heating removes the carrier and sinters adjacent nanoparticles into a conductive trace.
Camphorsulfonic acid protonates polyaniline, and a cresol solvent dissolves the protonated polymer. After aerosol deposition, solvent evaporation leaves a continuous film that conducts through the doped polymer.
An aqueous dispersion carries activated carbon, conductive carbon black, and a carboxymethyl cellulose binder onto a current collector. After drying, the carbon black connects the grains electrically, and electrolyte ions enter accessible pores and form an electrical double layer.
Sodium cholate adsorbs on the graphene surfaces and stabilizes the particles in water during atomization. After deposition, a water rinse removes residual surfactant from the dried coating and reduces resistance at contacts between flakes.
Shear mixing exfoliates graphite in N-methyl-2-pyrrolidone, which wets the exposed graphene surfaces and limits restacking in the liquid. Aerosol deposition places the flakes on a heated substrate, and solvent evaporation leaves an overlapping conductive network.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
Print an aqueous dispersion of graphene oxide particles with an atomic O/C ratio of at least 0.3 across interdigitated carbon electrodes on a polymer label. Dry the coating to form a continuous film that bridges the electrode gaps, and mount the label with the film exposed to the package headspace. Measure the film impedance at a fixed AC frequency and map it to relative humidity using a calibration curve measured at the operating temperature.
Spray an aqueous ink containing graphene oxide particles with an atomic O/C ratio of at least 0.3 and a polyvinyl alcohol binder onto a sealed paper surface. Apply overlapping passes to form a continuous wet film and dry it with warm air so the platelets pack into a layer predominantly parallel to the paper surface. The overlapping platelets lengthen the diffusion path for oxygen passing through the dry coating.
Substitute ozone-oxidized carbon black for the oxygenated graphene particles and disperse it in water with an acrylic latex binder. Screen-print a rectangular track across two copper busbars on a polyimide sheet and dry it to form a conductive particle network. Adjust the deposited thickness to set the track resistance, then apply a DC voltage across the busbars to heat the sheet.
Disperse 0.2 to 0.5 weight percent graphene oxide particles with an atomic O/C ratio of at least 0.3 in a 90 to 10 water-to-glycerol mixture by mass. Classify the dispersion to a particle lateral size of 0.5 micrometers or less and load it into a piezoelectric printhead with 25 micrometer nozzles. Print three to six passes on a substrate held at 50 °C, allowing each pass to dry before depositing the next.
Mount an aerosol jet printhead over a vacuum platen in a roll-to-roll web transport system and feed it an aqueous ink containing graphene oxide particles with an atomic O/C ratio of at least 0.3. Use the web encoder to trigger deposition at registered positions on a moving polymer film. Pass the printed web through a hot-air dryer and place an optical inspection camera ahead of the take-up roll to check line continuity.
Prepare two aqueous graphene oxide stock dispersions with different atomic O/C ratios of at least 0.3, and measure each stock's O/C ratio and carbon concentration by elemental analysis of washed, dried particle samples. For a target ratio between the two stock values, software calculates each stock volume using a carbon-weighted material balance and commands metering pumps to feed a stirred vessel. A load cell verifies each addition, and a separate water feed sets the final solids concentration.
Ultrasonication exfoliates graphite oxide in water into individual graphene oxide sheets. Centrifugation removes larger fragments and yields a dispersion enriched in sheets with lateral dimensions below 500 nanometers.
Controlled shear mixing separates graphite oxide into platelets that retain two to five stacked layers. Differential centrifugation removes coarse aggregates and retains the few-layer fraction for redispersion in the ink carrier.
Permanganate oxidation of graphite in sulfuric acid introduces hydroxyl, epoxide, and carboxyl groups. After washing and exfoliation, sensitivity-corrected oxygen and carbon peak areas from X-ray photoelectron spectroscopy give an atomic O/C ratio of 0.40 for the dried flakes.
Aqueous ascorbic acid partially reduces graphene oxide with an initial atomic O/C ratio above 0.40. The reaction time sets the final atomic O/C ratio to 0.33, measured on washed and dried flakes by X-ray photoelectron spectroscopy.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The heat produced by the detonation causes a temperature of at least 3000 K so as to generate graphene particles.A · US 2014/0335010 A1 · ¶ 7
A method of synthesizing high quality graphene for producing graphene particles and flakes is presented.B · US 2018/0072573 A1 · abstract
The survey XPS spectrum in FIG. 12(a) indicates that the graphene is very pure because the actual ratio of C to O is about 49:1.A · US 2014/0335010 A1 · ¶ 49
An empty cell means only that no passage was reproduced there.
Thus despite the usefulness of previous graphene synthetic methods, none appear to offer economical, eco-friendly, kilogram scale production of the material.A · US 2014/0335010 A1 · ¶ 6
In particular embodiments, the invention involves the detonation of a gas-phase hydrocarbon compound with a source of oxygen at relatively high temperatures to produce pristine graphene nanosheets without the use of catalytic materials.A · US 2014/0335010 A1 · ¶ 3
The lack of a suitable environmentally innocuous, high volume or “bulk” manufacturing method for the production of high-quality graphene restricts graphene for use in commercial applications.B · US 2018/0072573 A1 · ¶ 2
The method is particularly suitable for producing engineered graphene particles and flakes.B · US 2018/0072573 A1 · ¶ 1
patent.fyi, US 2026/0357094 A1, claim 1, first published 2026-11-20T10:10:52-05:00, https://patent.fyi/US20260357094/, SHA-256 0975613aff0c82a3240a3d22811cddb7fca21128a05e89c461b375664e235c6a