Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
1.2Measured bulk reference interval
What ifWhat if measurements on bulk reference specimens set the band-gap interval?
Measure diffuse reflectance for three coarse-grained specimens of the same composition and crystal phase. Extract the absorption edge using the same fitting procedure for each spectrum and use the mean edge energy plus or minus two sample standard deviations as the reference interval.
Section 2 · machine-generated
Variations
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
Other field of use
Optical attenuation reference for camera testing
Disperse chalcogenide perovskite particles with a mean diameter below 40 nm in a transparent resin and cure the resin between glass plates. Select a batch whose measured optical gap falls within the supplied hybrid-functional reference interval. Place the reference and a resin-only blank in a camera test fixture and illuminate them at wavelengths on both sides of the absorption edge. Divide the reference signal by the blank signal at each wavelength to track changes in the camera's relative spectral response.
Component substitution
Quasiparticle calculation for the reference gap
Replace the hybrid-functional calculation with a self-consistent GW calculation on the bulk crystal structure corresponding to the nanoparticle phase. Fit a linear relation between calculated quasiparticle gaps and measured bulk optical gaps using reference samples from the same composition family and a common measurement temperature. Form a reference interval extending 5% above and below the fitted optical gap. Compare the measured optical gap of the sub-40 nm particles with that interval.
Parameter or scale variation
Size fractionation at a fixed optical gap
Separate a 50 mL dispersion of a single chalcogenide perovskite composition by differential centrifugation to obtain fractions with target mean diameters of 8, 16, and 32 nm. Redisperse each fraction in the same solvent and verify its mean primary-particle diameter by transmission electron microscopy. Record an absorption spectrum for each fraction in a 1 mm cell at 25 °C and extract the optical gap using the same fitting procedure. Retain fractions whose measured gaps fall within the supplied bulk reference interval.
Temperature cycling with optical gap measurements
Seal sub-40 nm chalcogenide perovskite particles in a quartz cell with a transparent matrix rated for the test temperatures. Cycle the cell between −20 °C and 80 °C at 5 °C per minute, with a 10-minute hold at each endpoint. Measure the absorption edge at both endpoints and again after the cell returns to 25 °C. Compare the initial and recovered 25 °C gaps with the supplied reference interval and report endpoint shifts relative to the initial gap.
Combination with existing systems
Perovskite absorption filter on a photodiode
Disperse gap-matched chalcogenide perovskite particles with a mean diameter below 40 nm in a transparent binder. Coat the dispersion onto the outside of a silicon photodiode package window and cure the coating to form an optical filter. Select a particle composition whose absorption edge falls within the photodiode's response band. Measure the coated and uncoated detector responsivities under the same monochromatic illumination and adjust coating thickness to set attenuation on the high-energy side of the edge.
Automated or data-driven variant
Automated screening of particle size and gap
Load nanoparticle dispersions into an automated sampler that feeds a small-angle X-ray scattering cell and an optical transmission cell. Fit the scattering data with a particle form factor to estimate mean primary-particle diameter, and fit the blank-corrected optical absorption edge to estimate the gap. Retrieve the calculated hybrid-functional gap for the recorded composition and phase, and compute the supplied reference interval. Flag samples whose mean diameter is below 40 nm and whose measured gap falls within that interval.
Specific version of a part
Interval for a two-electronvolt input
Use a bulk hybrid-functional band gap of 2.0000 eV as the input. Multiply by 0.9286, add 0.3049 eV, and apply the five-percent tolerance to obtain an interval of 2.0540 to 2.2702 eV.
Interval comparison in millielectronvolts
Express the calculated band gap in millielectronvolts, multiply by 0.9286, and add 304.9 meV. Multiply the result by 0.95 and 1.05 to obtain the lower and upper bounds and compare the measured gap in the same units.
Cite aspatent.fyi, US 2026/0357132 A1, claim 1, first published 2026-11-20T10:48:41-05:00, https://patent.fyi/US20260357132/, SHA-256 dbf6664bbdad6b9c4fb6670da23d335860a08cbb624b479652948301754879b1