1.1Open conveyor for regeneration
A perforated ceramic belt carries the pellets in a shallow layer through a bank of radiant heaters. Air supplied through the belt oxidizes surface coke, and an overhead extraction hood collects the combustion gases.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A perforated ceramic belt carries the pellets in a shallow layer through a bank of radiant heaters. Air supplied through the belt oxidizes surface coke, and an overhead extraction hood collects the combustion gases.
The rings provide flow passages through the packed section and conduct heat across individual ring walls. During regeneration, hot dilute air passes through the packing and oxidizes coke on the exposed ring surfaces.
A thin pyrolytic carbon film covers selected faces of the fused silica insert. During regeneration, controlled pulses of dilute oxygen remove accumulated coke, and carbon oxide measurements at the outlet guide the end of each pulse sequence.
A dense alumina layer covers the hydrocarbon-facing surfaces of the metal insert and limits contact between the feed and exposed metal. During regeneration, dilute air flows over the alumina and oxidizes deposited coke.
A hydraulic drive pushes a segmented scraper through each isolated tube and breaks the coke layer into chips. A water flush carries the chips to a solids basket.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A heated reaction vessel sits in the exhaust duct of a ceramics kiln that removes organic binders from formed parts. The vessel holds stainless steel plates with graphite bands on part of each plate, and a wall heater controls the plate temperature. A mixing section upstream of the plates combines hydrocarbon-bearing kiln exhaust with metered air. During intervals of reduced binder release, the heated, oxygen-bearing stream oxidizes deposits on the plates.
Indirect-fired radiant tubes serve as the thermal element in a vessel fitted with partially graphite-coated metal plates. The sealed tubes run between banks of plates and transfer heat by radiation and convection as a hydrocarbon and air mixture flows through the banks. Burners fire into the tubes, which discharge combustion products through a separate flue. A thermocouple attached to a plate supplies feedback to the burner controller during deposit oxidation.
Open-weave graphite felt panels serve as the carbon-based surface composition on dense stainless steel plates. Perforated metal retainers hold the felt in recessed strips that leave exposed metal between adjacent panels. The plates mount on edge inside a heated vessel, with spacers forming flow channels for the hydrocarbon and oxidant mixture. The heater holds the plates at the deposit oxidation setpoint while the flowing gas contacts the felt and the exposed metal.
Three identical heated vessels connect in parallel, each with a partially carbon-coated metal cartridge and independently metered hydrocarbon and oxidant feeds. Each vessel has a service branch sized for half the nominal process flow and a separate exhaust branch for the deposit oxidation step. Two vessels carry the process flow while the third receives a lower hydrocarbon flow with continued oxidant addition for a 15-minute interval. The controller then returns that vessel to service and rotates another vessel into the deposit oxidation step.
A gas-to-gas recuperator connects the outlet of a heated reaction vessel to its incoming hydrocarbon feed. The vessel contains a partially graphite-coated metal cartridge, and the hot outlet gas transfers heat across the recuperator wall to the incoming feed. A metering valve introduces air downstream of the recuperator on the feed side, and a static mixer distributes it before the mixture enters the vessel. The vessel heater supplies the remaining heat during deposit oxidation.
Pressure taps at both ends of a partially carbon-coated metal cartridge connect to a differential pressure transmitter, and a thermocouple measures the cartridge temperature. A controller compares the measured pressure drop with a clean-cartridge baseline indexed by inlet flow and gas temperature. When the difference stays above a set threshold, the controller reduces hydrocarbon flow, maintains metered oxidant flow and raises the heater setpoint within a preset temperature limit. The controller restores the service settings when the pressure drop returns to a specified band around the baseline.
A vertical cylindrical steel shell holds removable composite inserts above a perforated support plate. An inlet plenum and a perforated distributor spread the gas across the insert channels.
Corrugated nickel alloy sheets form the metal substrate. Vapor deposition applies pyrolytic carbon to selected channel faces, while masking leaves the attachment tabs exposed.
Three independently controlled resistance heater bands surround the reaction vessel. Thermocouples at the inlet, middle, and outlet of the insert bed provide feedback to the heater controllers.
Mass flow controllers meter methane and dilute oxygen in nitrogen into a static mixer upstream of the vessel. The controllers maintain an oxygen concentration of 0.1 mol.% in the combined inlet stream.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
The reduction reactor 104 includes a reactor chamber 108 and an aperture 110 through which concentrated solar energy is configured to pass into the reactor chamber 108.B · US 2024/0309283 A1 · ¶ 29
In yet another embodiment the present invention is method of treating a sulfur-containing hydrocarbon heavy feed comprising asphaltenes, tar sands, bitumens, heavy petroleum or mixtures thereof, comprising the steps of: mixing the sulfur-containing hydrocarbon heavy feed comprising asphaltenes with a natural petroleum solvent and an acidified silica to form a mixture; oxidizing the sulfur in the mixture in air or in a mixture of air and O2 at a temperature between 120° C. andA · US 2013/0264245 A1 · ¶ 19
The difference with this embodiment is that heating elements 508 are located in the furnace of reduction zone 518.B · US 2024/0309283 A1 · ¶ 75
An empty cell means only that no passage was reproduced there.
From the economic and environmental point of view, it would be more suitable if low-temperature and low-pressure systems could be developed to remove sulfur from fuels.A · US 2013/0264245 A1 · ¶ 8
One advantage of using these techniques is that sulfur can be removed at relatively low temperatures and atmospheric pressure.A · US 2013/0264245 A1 · ¶ 10
Long-duration thermal storage is a significant challenge due to thermal losses inherent to all high temperature systems.B · US 2024/0309283 A1 · ¶ 3
For example, the present fuel can be advantageously stored at about room temperature, for many months and optionally in the open air, without substantial loss of its energy storage potential.B · US 2024/0309283 A1 · ¶ 7
patent.fyi, US 2026/0357143 A1, claim 1, first published 2026-11-20T10:48:41-05:00, https://patent.fyi/US20260357143/, SHA-256 1e7a89708d18ab5e77de9e9a959dc7ed923d27b0a5b29913d6fc74e8dba4d9ac