1.1Circular access port
The port diameter exceeds the sheet width so the sheet passes edge-first while held upright. Guide rails inside the vessel receive the sheet edges, and a gasketed cap closes the port.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
The port diameter exceeds the sheet width so the sheet passes edge-first while held upright. Guide rails inside the vessel receive the sheet edges, and a gasketed cap closes the port.
A hinged lid exposes a square opening above two upright guide channels. The sheet slides down the channels to a bottom stop, and a latch compresses the lid gasket against the rim.
The sheet passes edge-first through a side slot and slides along two level ledges. A perforated plate between the ledges supports the sheet and lets liquid reach its underside.
Two inclined rails align with a slot near the upper end of the vessel. The sheet slides down the rails until its lower edge reaches a stop that holds it above the vessel floor.
A thin porous cylinder passes lengthwise through a slot wider than its diameter. An upright socket seats the cylinder, and side ports admit liquid to its lower end.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A rectangular tank receives a flat glass coupon through a straight slit in a fixed top flange. Two grooved rails below the slit engage the coupon edges and hold the coupon upright above the tank floor. A lower inlet feeds rinse water to both faces of the coupon, and an overflow port below the slit sets the water level.
A rectangular cell receives a coated metal panel through a slit and holds it upright between insulating edge guides. A spring contact grips the dry upper edge of the panel, and a counter electrode runs parallel to its immersed face. A fixed amount of electrolyte sets the immersion line, and a meter applies a small alternating voltage and records impedance over time.
Flat polypropylene panels form the vessel body, with welded seams joining the side panels to a flat base. Two parallel polypropylene strips span the top and define the slit between their inner edges. A removable polypropylene rack rests on the base and supports an inserted sheet by its lower corners while leaving both faces exposed to the liquid.
A chamber measuring 30 mm wide, 5 mm deep, and 80 mm tall receives a 25 mm wide, 0.5 mm thick transparent test strip through a 27 mm by 2 mm slit. Two edge guides align the strip with the slit and center it between the broad chamber walls. A stop 10 mm above the base supports the strip, and a fill mark 55 mm above the base sets the immersed length at 45 mm.
A slit-entry vessel for material soak testing sits inside a recirculating temperature-controlled water bath, with the slit above the bath waterline. Internal guides hold the test sheet vertically in a separate liquid inside the vessel. Bath water circulates around the exterior walls, and heat passes through those walls to the test liquid.
A motorized gripper lowers a polymer test sheet through the slit until it reaches a fixed vertical stop. Two optical liquid-level sensors attach to a transparent wall at the drain endpoint and the target fill height. A controller runs a fill pump until the upper sensor detects liquid, holds the sheet in place for a programmed interval, and opens a drain valve until the lower sensor clears.
A molded polypropylene top wall contains a straight slot with rounded entry edges. The slot length exceeds the sheet width, and its gap exceeds the sheet thickness so the sheet slides vertically into the vessel.
Two straight silicone lips define a narrow slit across the vessel lid. The lips flex apart as the sheet passes between them and return to their resting position after the sheet clears the lid.
Two molded channels sit directly below the slit and receive the opposite edges of the sheet. A ledge at the base supports the lower edge while the channels hold the sheet upright.
A thin frame grips the sheet along its side edges and passes vertically through the slit. A flange at the top of the frame rests on the slot rim and sets the depth of the suspended sheet.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
As shown in FIG. 2, each culture vessel 2 has an opening 5 at one end thereof and is provided with a vessel main unit 6 that can accommodate the cells 100 in the interior thereof and a lid 7 that is attached to the opening 5 to seal the vessel main unit 6.A · US 2015/0259640 A1 · ¶ 13
The cell culture vessel 100 has a port or aperture 105 (shown in FIG. 1 covered by a cap 104) and a neck 112 connecting the port or aperture 105 to the cell culture chamber 103.B · US 2020/0131461 A1 · ¶ 31
An empty cell means only that no passage was reproduced there.
In other words, when, as a result of microscope observation, the culturing state and the proliferation state are not satisfactory, it is necessary to return the culture vessel into the culturing apparatus again and to continue the culturing, and thus, the work performed is wasted and the risk of contamination by other cells such as bacteria or the like and other contaminants such as viruses or the like is increased.A · US 2015/0259640 A1 · ¶ 4
On the other hand, if the culturing state and the proliferation state are not checked at an appropriate timing, there is a risk of missing the appropriate timing for transferring the cells.A · US 2015/0259640 A1 · ¶ 4
In additional embodiments, the cell culture vessel has structures for introducing and removing media below the porous material or through the porous material without disturbing the media residing above cells resting in the microcavities of the microcavity array.B · US 2020/0131461 A1 · ¶ 6
The above embodiments are exemplary and can be provided alone or in any combination with any one or more embodiments provided herein without departing from the scope of the disclosure.B · US 2020/0131461 A1 · ¶ 7
patent.fyi, US 2026/0357176 A1, claim 1, first published 2026-11-20T11:28:11-05:00, https://patent.fyi/US20260357176/, SHA-256 8807e8486f9a860b068d74ac51d5b168d82393d6d19cad38203a09254d3e59b5