1.1Horizontal reciprocating platform
A motor-driven crank moves a carriage along two parallel rails while the platform stays level. Each reversal drives liquid toward the opposite end of the enclosure and produces a traveling wave.
Generated automatically. Not reviewed by a person. Not legal advice or an opinion.
Questions about how individual parts of claim 1 might be changed. A question may describe something different from what the claim language recites, or a version of it; no view is offered on which.
A motor-driven crank moves a carriage along two parallel rails while the platform stays level. Each reversal drives liquid toward the opposite end of the enclosure and produces a traveling wave.
A spring-loaded linkage carries a thermal panel from an independent frame. A ball joint lets the panel follow the changing angle of the enclosure, and flexible hoses carry heat transfer liquid between the panel and the control unit.
Thermoelectric modules sit between a solid aluminum spreader and an external finned heat sink. A controller reverses the direct-current polarity to switch the spreader between heating and cooling.
An enclosure temperature sensor feeds a controller that switches paired supply and return valves between a warm service loop and a cool service loop. The selected loop circulates liquid through the channel, and both valve paths close when the measured temperature enters the setpoint band.
Stand-offs hold the enclosure above a liquid-heated panel with a high-emissivity surface. The panel transfers heat across the gap by infrared radiation, and a sensor on the enclosure wall provides feedback to the liquid temperature controller.
Further arrangements of the same subject matter, described here as of the publication date at the foot of this page.
A sealed flexible pouch containing a waterborne coating sits on the heat transfer surface of a pivoting platform and is held by edge clips. A recirculating temperature control unit passes water through a channel beneath the contact surface. The controller alternates warm and cool holds while the platform rocks the pouch to simulate motion during transport. At the end of each hold, an optical sensor measures light transmission through a clear section of the pouch with the platform parked level.
A reversible thermoelectric module and a liquid heat exchanger replace the conventional heater and refrigeration assembly in a stationary temperature control unit. One face of the module contacts the heat exchanger, and the other contacts a fan-cooled heat sink. A pump circulates water through the exchanger and the channel in the rocking platform, with flexible hose loops routed near the pivot. A temperature controller varies the module current and reverses its polarity to switch between heating and cooling.
A 300 by 240 mm rocking deck carries four 100 mL pouches of aqueous test liquid in a two-by-two layout. Each pouch rests on a separate 100 by 80 mm aluminum block with an internal water channel and its own recirculating circuit. Polymer spacers separate the blocks from the deck and from adjacent blocks, and flexible supply and return lines pass near the pivot. The deck rocks through ±5 degrees at 12 cycles per minute while each circuit supplies 0.3 L/min of water at a setpoint between 15 and 40 degrees Celsius.
A rocking platform sits inside a programmable humidity chamber and supports a sealed aqueous materials test pouch on a channeled heat transfer element. Flexible supply and return hoses run from the moving element to fixed bulkhead fittings, which connect to a recirculating water unit outside the chamber. The chamber regulates air humidity while the water unit regulates the pouch contact temperature using a surface sensor on the element. A removable drip tray beneath the platform collects condensate during cycles below the chamber air dew point.
A thin-film resistance temperature sensor adheres to the exposed wall of a sealed test-fluid pouch, and a second sensor measures water temperature at the platform channel inlet. The pouch sensor cable follows the flexible hoses through a service loop near the pivot. An outer control loop adjusts the inlet water setpoint from the pouch wall temperature error, and a faster inner loop adjusts heating or cooling to reach that setpoint. The controller limits the commanded inlet temperature and records both readings throughout each run.
An inline flow sensor in the stationary return line measures water flow through the channel under a sealed materials test pouch. A rotary encoder on the platform pivot supplies the tilt angle to a controller, which groups flow readings by angle and direction of travel. If flow falls below a configured threshold at the same angle on three consecutive cycles, the controller parks the platform level and checks flow again. The controller disables heating and cooling if flow remains below the threshold and records the angle and flow readings for troubleshooting.
A cradle bolts to a vertical face of the platform and supports the enclosure on a lower ledge. A spring-loaded retaining frame presses the enclosure against a thermal panel on the cradle as the platform rocks.
Two coaxial trunnions support the platform in bearings on the base and define a horizontal pivot axis. A geared motor and crank linkage drive the platform through 6 degrees on either side of level.
A serpentine groove runs across an aluminum plate bolted to the platform. A gasketed cover seals the groove to form a channel with inlet and outlet ports at opposite ends.
A circulation pump sends a water and propylene glycol mixture from a reservoir through the platform channel and back. A controller uses an enclosure temperature sensor to command either an immersion heater or a refrigeration heat exchanger in the reservoir.
Two flexible polymer sheets joined along patterned seams form a channel inside a pad mounted on the platform. The pad conforms to the enclosure underside while a pump circulates temperature-controlled water through the channel.
Passages reproduced word for word from two earlier-published U.S. patent documents, placed beside the language of claim 1. No characterization is offered. Each passage is marked A or B for the document it comes from; ¶ numbers are the paragraph numbers in the USPTO’s published full text of that document.
In the present methods, culture medium and cells contact only a presterile, chamber that is positioned on a special rocking platform. The rocking motion of the platform induces waves in the culture fluid and thereby provides continual mixing and oxygen transfer, resulting in a robust environment for cell growth.A · US 2016/0340633 A1 · ¶ 75
An incubation device (V), comprising a multiplicity of rocking platforms (W), which are respectively mounted tiltably about a respective axis (A), a respective rocking platform (W) comprising a respective reception device (AN) for mechanically reversible reception of a respective incubation tray (I), furthermore comprising a common drive unit (AE) for common generation of respective rocking movements of the respective rocking platforms, in particular from a neutral position (B · US 2019/0284519 A1 · ¶
The incubation device according to embodiment 8, wherein the rocking platform (W) furthermore comprises a heating device (HZ) for heating the bottom (B). 10.B · US 2019/0284519 A1 · ¶
This compact unit is fitted with integral features such as aeration, heating, and temperature control.A · US 2016/0340633 A1 · ¶ 158
An empty cell means only that no passage was reproduced there.
However one challenge in perfusion/suspension culture is how to retain the cells in the bioreactor.A · US 2016/0340633 A1 · ¶ 4
There is a need in the field for techniques which reduce human intervention and cross-contamination during the process of culturing cells, including pluripotent stem cells and/or differentiated human cells.A · US 2016/0340633 A1 · ¶ 5
One unsolved problem is the scarcity and expense of reagents and sample material.B · US 2019/0284519 A1 · ¶ 8
This saves on reagents and space, and allows a sample once obtained to provide enough starting material for a large number of diagnostic studies.B · US 2019/0284519 A1 · ¶ 8
patent.fyi, US 2026/0357180 A1, claim 1, first published 2026-11-20T11:28:11-05:00, https://patent.fyi/US20260357180/, SHA-256 2ee5537a095c828271816027705e00e01a890fc87a8e37ae531994c822c10ae2